MC尼龙重载承压地板井下巷道铺设工艺研究

我国煤矿井下无轨运输混凝土路面铺设成本高，并且受开采应力、巷道底板地质条件等影响，其应用受到限制。重载车辆的频繁碾压极易使路面发生损坏，从而影响正常开采效率还带来高昂的维护费用。为解决这一问题，采用MC尼龙重载承压地板代替传统混凝土铺设路面，进行了MC尼龙重载承压地板井下巷道铺设的工艺研究。通过对承压板井下铺设方案的制定、承压地板型式的研发、地板的整体连接及稳定性研发等，实现了高效的作业效率，更为安全、清洁的作业环境以及更低的成本，进而达到了“以塑代混凝土”的实际示范意义。该铺设工艺为井下无轨运输的采区路面、工作面搬家通道、临时路面以及其他应急路面、硐室地板的应用提供了良好的方案借鉴。     

恒湿文物展柜用吸附式空气取水方法

博物馆恒湿文物展柜的湿度控制至关重要，为实现展柜的自动恒湿功能，本文基于吸附式空气取水原理，提出了一种将环境水汽自动补充至恒湿文物展柜系统水箱的方法，并搭建了相应的小型空气取水装置，证明了该方法的可行性；同时，构建了传热传质耦合的空气取水装置数学模型，在获取环境温湿度对装置取水量的影响规律后，分析加热功率和吸附床结构对装置单位能耗取水量的影响；此外，为便于装置的后期推广应用，提出了两个基于吸附床高度和直径的量纲为1参数。结果表明：进口空气的温度对取水量影响较小，但进口空气的湿度对取水量影响较明显，取水量随着湿度增加而增加；加热功率存在最优值，单位能耗取水量随着加热功率先增大后减小；在当前几何参数组合下，两个量纲为1参数η=2、β=4时，装置的单位能耗取水量最高。     

超亲水毛细芯环路热管启动及热性能分析

为解决电子设备高热通量下的散热问题，采用H₂O₂氧化法对烧结毛细芯进行了超亲水改性，研究了毛细芯表面润湿性对吸液性能的影响。并将改性后的超亲水毛细芯应用到环路热管内，研究了倾斜角度及加热功率对超亲水毛细芯环路热管的换热特性的影响。实验结果表明：超亲水毛细芯的吸液速度增加，吸液时间较亲水毛细芯减小了3.52ms；与普通亲水毛细芯环路热管相比，在加热功率Q=200W时，超亲水毛细芯环路热管蒸发器中心温度降低了约6.0℃，在Q=20W时启动时间与温度分别降低了33s与2.5℃。同时发现超亲水毛细芯环路热管在正重力状态时的运行温度更低，热阻较小，最低热阻仅为0.084℃/W。     

热处理对等离子喷涂铁基非晶合金涂层微观结构和耐腐蚀性能的影响

采用等离子喷涂技术在Q235钢基体上制备Fe48Cr15Mo14C15B6Y2非晶合金涂层,之后对涂层进行200,300,500,600,700℃热处理,研究了热处理对涂层微观结构、耐电化学腐蚀性能和耐均匀腐蚀性能的影响。结果表明:随着热处理温度的升高,涂层的非晶含量降低,孔隙率先减小后增大,经300℃热处理后涂层的孔隙率最低,且低于未热处理涂层的;热处理后涂层中的晶体相主要包括α-Fe,Fe-Cr,Fe63Mo37,Fe3C等;随着热处理温度的升高,涂层的自腐蚀电流密度先减小后增大,经300℃热处理后,自腐蚀电流密度最小,涂层的耐电化学腐蚀性能最好;经过热处理后,涂层在NaCl溶液中浸泡31d后的单位面积质量损失减小,且热处理温度越高,单位面积质量损失越小,涂层的耐均匀腐蚀性能提高。     

在轨维修后端模块接口机构的研究

在轨维修可以大大的延长空间科学仪器的使用寿命,节省大量的经济成本。为了实现空间望远镜后端模块的在轨操作和更换,设计了一套与之对应的接口机构,能够解决在轨快速定位与安装。根据321运动学定位准则,详细介绍了该接口机构的内部组成和工作原理;然后把该接口机构与后端模块进行组件级有限元仿真,仿真结果表明一阶模态远高于整机基频可以有效地避免发射时候的共振;设计了一套平面内的工装来模拟后端模块,利用等效质量法对整个机构进行重力卸载;搭建实验平台,利用激光跟踪仪来测量整个后端模块的重复定位安装精度,实验数据表明,X,Y,Z 3个方向的重复平移定位误差分别为±5.58μm,±3.24μm及±3.63μm,优于总体指标±10μm;热实验结果表明整个机构可以完全释放由于温度变化产生的形变,具有很高的热稳定性;使入射光线和靶面的相对位置持续稳定,保证了较高的成像质量。为其他空间在轨维护装置提供强有力的参考价值。     

Flame extension and the near field under the ceiling for travelling fires inside large compartments

Structures need to be designed to maintain their stability in the event of a fire. The travelling fire methodology (TFM) defines the thermal boundary condition for structural design of large compartments of fires that do not flashover, considering near field and far field regions. TFM assumes a near field temperature of 1200°C, where the flame is impinging on the ceiling without any extension and gives the temperature of the hot gases in the far field from Alpert correlations. This paper revisits the near field assumptions of the TFM and, for the first time, includes horizontal flame extension under the ceiling, which affects the heating exposure of the structural members thus their load-bearing capacity. It also formulates the thermal boundary condition in terms of heat flux rather than in terms of temperature as it is used in TFM, which allows for a more formal treatment of heat transfer. The Hasemi, Wakamatsu, and Lattimer models of heat flux from flame are investigated for the near field. The methodology is applied to an open-plan generic office compartment with a floor area of 960 m² and 3.60 m high with concrete and with protected and unprotected steel structural members. The near field length with flame extension (fTFM) is found to be between 1.5 and 6.5 times longer than without flame extension. The duration of the exposure to peak heat flux depends on the flame length, which is 53 min for fTFM compared with 17 min for TFM, in the case of a slow 5% floor area fire. The peak heat flux is from 112 to 236 kW/m² for the majority of fire sizes using the Wakamatsu model and from 80 to 120 kW/m² for the Hasemi and Lattimer models, compared with 215 to 228 kW/m² for TFM. The results show that for all cases, TFM results in higher structural temperatures compared with different fTFM models (600°C for concrete rebar and 800°C for protected steel beam), except for the Wakamatsu model that for small fires, leads to approximately 20% higher temperatures than TFM. These findings mitigate the uncertainty around the TFM near field model and confirm that it is conservative for calculation of the thermal load on structures. This study contributes to the creation of design tools for better structural fire engineering.     

雷达发射机浮动板调制器与故障检测电路的设计

提出了一种改进的浮动板调制器和对正负偏电压的故障检测电路,利用MOSFET寄生电容特性,通过固定脉宽窄脉冲控制调制脉宽,通过增加负偏MOSFET提高输出负偏电压。对故障检测电路进行仿真实验,通过模拟故障,验证故障检测报警信号发生时间均在微秒级别。完成样机的搭建,利用多重方式解决高压绝缘问题,并对其加电进行试验验证,分析实验波形,证明此电路满足设计要求并且具有可行性。     

不同润湿表面液体沸腾的分子动力学模拟

采用分子动力学方法研究纳米尺度下液氩在过热基板上的沸腾过程。通过调节固液间相互作用的方式改变壁面润湿性，模拟并分析了壁面润湿性对沸腾过程中能量传递和液体运动情况的影响。结果表明：不同润湿性表面均会发生固液分离的现象，但是固体表面附近吸附的氩原子数密度随润湿性增强而增大；润湿性较强时，液体的能量上升快，热通量高，液体内部温度梯度大，发生固液分离时间早，系统中氩的温度和能量低，上升过程中液氩密度、厚度变化小；润湿性较弱时，液体的能量上升慢，热通量小，液体内部温度梯度小，发生固液分离时间延后，系统中氩的温度、能量更高，上升过程中液氩密度、厚度变化较大。下部气体压力整体上大于上部气体压力，发生固液分离时润湿性越强的表面上液体上下压差越大，首次上升过程能达到的高度越高，所需时间越短。     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

Development of mobile miniature natural gas liquefiers

With increasing consumption of natural gas (NG), small NG reservoirs, such as coalbed methane and oil field associated gas, have recently drawn significant attention. Owing to their special characteristics (e.g., scattered distribution and small output), small-scale NG liquefiers are highly required. Similarly, the mixed refrigerant cycle (MRC) is suitable for small-scale liquefaction systems due to its moderate complexity and power consumption. In consideration of the above, this paper reviews the development of mobile miniature NG liquefiers in Technical Institute of Physics and Chemistry (TIPC), China. To effectively liquefy the scattered NG and overcome the drawbacks of existing technologies, three main improvements, i.e., low-pressure MRC process driven by oil-lubricated screw compressor, compact cold box with the new designed heat exchangers, and standardized equipment manufacturing and integrated process technology have been made. The development pattern of “rapid cluster application and flexible liquefaction center” has been eventually proposed. The small-scale NG liquefier developed by TIPC has reached a minimum liquefaction power consumption of about 0.35 kW·h/Nm³. It is suitable to exploit small remote gas reserves which can also be used in boil-off gas reliquefaction and distributed peak-shaving of pipe networks.